View TM162JBC7-1SPECS_7789481.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

specification for lcd module model no. tm162jbc7-1 prepared b y : date: checked b y : date: verified b y : date: approved by: date: tianma microelectronics co., ltd rev. 1.0
1/22 rev. 1.0 revision record date ref. page revision no. revision items check & approval
2/22 rev. 1.0 1 general specifications: 1.1 display type: stn 1.2 display color: display color* 1 : blue-black background* 2 : yellow-green 1.3 polarizer mode: transflective /positive 1.4 viewing angle: 6:00 1.5 driving method: 1/16 duty 1/5 bias 1.6 backlight: led 1.7 controller: s6a0069x01-c0cx (ks0066up-00cc) 1.8 data transfer: 8 bit parallel 1.9 operating temperature: 0----+50 ?? storage temperature: -20----+60 ?? 1.10 vdd: 5.0v 1.11 lcd operating voltage: 4.7v 1.12 outline dimensions: refer to outline drawing on next page 1.13 dot matrix: 16 characters ? 2 lines 1.14 dot size: 0.55 ? 0.55(mm) 1.15 dot pitch: 0.60 ? 0.60 (mm) 1.16 weight: about 35g * 1 color tone is slightly changed by temperature and driving voltage. * 2 color tone will be changed by backlight.
3/22 rev. 1.0 2 outline drawing
4/22 rev. 1.0 3 lcd module part numbering system tm 162 j b c 7 - 1 optional ic indicator (for factory use) modification code designator backlight type c:transflective led backlight lcd type b:yellow-green stn mode positive module series module type 3 digits indicating 16columns ? 2 rows t: tianma m: module
5/22 rev. 1.0 4 circuit block diagram
6/22 rev. 1.0 5 absolute maximum ratings item symbol min. max. unit remark power supply voltage v dd - v ss -0.3 7 .0 lcd driving voltage v lcd - 13.0 v operating temperature range t op 0 +50 storage temperature range t st -20 +60 ?? no condensation
7/22 rev. 1.0 6 electrical specifications and instruction code 6.1 electrical characteristics item symbol min. typ. max. unit supply voltage (logic) v dd - v ss 4.5 5.0 5.5 v supply voltage (lcd drive) v lcd - 4.7 - v high v ih ? v dd =5.0 ? 0.7v dd - v dd +0.3 v input signal voltage low v il ? v dd =5.0 ? -0.3 - 0.2 v dd v supply current (logic) i dd (v dd - v ss =5.0v) - 1.5 - ma supply current (lcd drive) i ee - 0.4 - ma supply current (led drive) i led (v led =4.2v dc) - - 140 ma
8/22 rev. 1.0 6.2 interface signals pin no. symbol level description 1 vss 0v gnd 2 vdd +5v power supply voltage for logic and lcd(+) 3 v0 +0.3 power supply voltage for lcd(-) 4 rs h/l selects registers (h: data l:instruction) 5 r/w h/l read /write signal(h:read;l:write) 6 e h/l enable signal 7 db0 h/l data bit0 8 db1 h/l data bit1 9 db2 h/l data bit2 10 db3 h/l data bit3 11 db4 h/l data bit4 12 db5 h/l data bit5 13 db6 h/l data bit6 14 db7 h/l data bit7 a led+ 4.2v backlight power supply pin ? + ? k led- 0v backlight power supply pin ? - ?
6.3 interface timing chart ac characteristics(v =4.5v~5.5v,ta=-30~+85 7 0rgh &kdudfwhulvwlf 6\pero 0lq? 7\s? 0d[? 8qlw :ulwhy0rgh ?5 h i huywry) l j e?? (y&\fohy7lph wf e e qv (y5lvhy?y)dooy7lph w 5 ?w ) ee? (y3xovhy:lgwky?+ljk?y/rz? wz ? e e 5?: y dq g y56 y 6h w xsy 7 l p h w v x e e 5?:ydqgy56y+rogy7lph w + e e 'dwdy6hwxsy7lph wvx? ? e e 'dwdy+rogy7lph w +? e e 5hdgy0rgh ?5hihuywry)lje?? (y&\fohy7lph wf e e qv (y5lvhy?y)dooy7lph w 5 ?w ) ee? (y3xovhy:lgwky?+ljk?y/rz? wz ? e e 5?:ydqgy56y6hwxsy7lph wvx e e 5?:ydqgy56y+rogy7lph w + e e 'dwdy2xwsxwy'hod\y7lph w ' ee? 'dwdy+rogy7lph w '+ e e 9/22 rev. 1.0
)ljxuhy?y?yy:ulwhy0rghy7lplqjy'ldjudp )ljxuhy?y?yy5hdgy0rghy7lplqjy'ldjudp 9 ,+ 9 ,/ 9 ,/ w 68 w k w z 9 ,/ 9 ,+ 9 ,/ 9 ,+ 9 ,/ 9 ,+ 9 ,/ 9 ,+ 9 ,/ 9 ,/ w & w i w u w 68? w k? 9dolg 'dwd 56 5?: ( '%a'%? w k 9 ,+ 9 ,/ w 68 w k w k w z 9 ,+ 9 ,/ 9 ,+ 9 ,/ 9 ,+ 9 ,/ 9 ,+ 9 ,/ 9 ,/ w & w i w u 9dolg 'dwd 56 5?: ( '%a'%? 9 ,+ 9 ,+ w ' w '+ 10/22 rev. 1.0
+(>1 127(?y:khqydqy038ysurjudpyzlwkyfkhfnlqjywkhy%xv\y)odj?'%??ylvypdgh?ylwypxvwyehyqhfhvvdu\y??)rvfylv yyyyyyyyyyyyyqhfhvvdu\yiruyh[hfxwlqjywkhyqh[wylqvwuxfwlrqye\ywkhyidoolqjyhgjhyriywkhy?(?yvljqdoydiwhuywkhy%xv\y)odjy?'%??y yyyyyyyyyyyyyjrhvywry|/rz?y y y,q v w u x f w lrqy 7 d eoh ,qvwuxfwlrq ,qvwuxfwlrqy&rgh 'hvfulswlrq ([hfxwlrqy wlphy?irvf y ??yn+]? 5 6 5? : '% ? '% ? '% '% '% '% ? '% '% &ohdu 'lvsod\ y:u l why|? + y wry'' 5 $0 y dq g yv h wy y''5$0ydgguhvvywry|+yiurpy$& ?ypvy 5hwxuqy +rph e y6hwy''5$0ydgguhvvywry|+y yiurpy$&ydqgyuhwxuqyfxuvruywrylwv yruljlqdoysrvlwlrqyliyvkliwhg?y y7khyfrqwhqwvyriy''5$0yduhyqrwy yfkdqjhg? ?ypv (qwu\y0rghy 6hwy ,?'6+ y$vvljqyfxuvruyprylqjygluhfwlrqy ydqgyhqdeohywkhyvkliwyriyhqwluhyglvsod\?y ?y p v 'lvsod\y21? 2))y&rqwuro '&% y6hwyglvsod\?'??yfxuvru?&??y ydqgyeolqnlqjyriyfxuvru?%?yrq?riiy yfrqwuroyelw? ?y p v &xuvruyru y'lvsod\y 6kliw 6?&5?/e e y6hwyfxuvruyprylqjydqgyglvsod\y yvkliwyfrqwuroyelw?ydqgywkhygluhfwlrq?y yzlwkrxwyfkdqjlqjyriy''5$0ygdwd?y ?y p v )xqfwlrqy6hw '/1)e ey y6hwylqwhuidfhygdwdyohqjwky?'/?y y?eelw?eelw??yqxpehuvyriyglvsod\yolqh y?1?y?eolqh?eolqh?ydqg?yglvsod\ yirqwyw\shy?)? u grwv? u ?ygrwv? ?y p v 6hwy&*5$0y $gguhvv $& $& $& $&? $& $& y6hwy&*5$0ydgguhvvylqydgguhvvy yfrxqwhu? ?y p v 6hwy''5$0y $gguhvv $&? $& $& $& $&? $& $& y6hwy''5$0ydgguhvvylqydgguhvvy yfrxqwhu? ?y p v 5hdgy%xv\y )odjydqgy $gguhvv %) $&? $& $& $& $&? $& $& y:khwkhuygxulqjylqwhuqdoyrshudwlrq yruyqrwyfdqyehynqrzqye\yuhdglqjy%)?y y7khyfrqwhqwvyriydgguhvvyfrxqwhu yfdqydovryehyuhdg? y p v :ulwhy'dwdywry 5$0 '? '? ' ' ' '? ' ' y:ulwhygdwdylqwrylqwhuqdoy5$0y y?''5$0?&*5$0?? y p v 5hdgy'dwdy iurpy5$0 '? '? ' ' ' '? ' ' y5hdgygdwdyiurpylqwhuqdoy5$0y y?''5$0?&*5$0?? y p v 11/22 rev. 1.0
)+0- ;:,6d**))?**7 )+0- ;:,6d**))?**7 12/22 rev. 1.0
13/22 rev. 1.0 7 optical characteristics 7.1 optical characteristics ta=25 ?? item symbol condition min. typ. max. unit | x | y =0 ?? -35 -- 20 viewing angle | y c r 2 | x =0 ?? -30 -- 30 deg contrast ratio c r | x =0 ?? | y =0 ?? 4.0 - - turn on t on - - 250 response time turn off t off | x =0 ?? | y =0 ?? - - 250 ms
7.2 definition of optical characteristics 7.2.1 definition of viewing angle top top bottom bottom 7.2.2 definition of contrast ratio brightness state selected brightness state unselected = b2/b1 = ratio contrast measuring conditions: 1) ambient temperature: 25 ; 2) frame frequency: 64hz 7.2.3 definition of response time turn on time: t on = t d + t r turn off time: t off = t d + t f measuring condition: 1) lcd operating voltage: 4.7v 2) frame frequency: 64hz 14/22 rev. 1.0
15/22 rev. 1.0 8 reliability 8.1 content of reliability test ta=25 ?? no. test item content of test test condition 1 high temperature storage endurance test applying the high storage temperature for a long time 60 ?? 96h restore 4h at 25 ?? 2 low temperature storage endurance test applying the low storage temperature for a long time -20 ?? 96h restore 4h at 25 ?? 3 high temperature operation endurance test applying the electric stress (voltage | current) and the thermal stress to the element for a long time 50 ?? 96h 4 low temperature operation endurance test applying the electric stress under low temperature for a long time 0 ?? 96h 5 high temperature /humidity storage endurance test applying the high temperature and high humidity storage for a long time 40 ?? 90%rh 96h restore 4h at 25 ?? 6 temperature cycle endurance test applying the low and high temperature cycle -20 ????? 25 ????? 60 ????? 25 ?? 30min 5min 30min 5min ??????????????? 1 cycle -20 ?? /60 ?? 10 cycles 7 vibration test (package state) endurance test applying the vibration during transportation 10hz~150hz, 50m/s 2 , 40min 8 shock test (package state) endurance test applying the shock during transportation half- sine wave, 100m/s 2 , 11ms 9 atmospheric pressure test endurance test applying the atmospheric pressure during transportation by air 40kpa 16h restore 2h
16/22 rev. 1.0 8.2 failure judgment criterion test item no. criterion item 12 3 4 56789 failure judgement criterion basic specification out of the basic specification electrical specification out of the electrical specification mechanical specification out of the mechanical specification optical characteristic out of the optical specification note for test item refer to 8.1 remark basic specification = optical specification + mechanical specification
17/22 rev. 1.0 9 quality level inspection examination or test at t a =25 ?? (unless otherwise stated) min. max. unit il aql external visual inspection under normal illumi-nation and eyesight condition, the dis-tance between eyes and lcd is 25cm. see appendix a ii major 1.0 minor 2.5 display defects under normal illumi-nation and eyesight condition, display on inspection. see appendix b ii major 1.0 minor 2.5 note: major defects: open segment or co mmon, short, serious damages, leakage miner defects: others sampling standard conforms to gb2828
18/22 rev. 1.0 10 precautions for use of lcd modules 10.1 handling precautions 10.1.1 the display panel is made of gla ss. do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 if the display panel is damaged a nd the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 do not apply excessive force to th e display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 the polarizer covering the display surface of the lcd m odule is soft and easily scratched. handle this polarizer carefully. 10.1.5 if the display surface is contamin ated, breathe on the surface and gently wipe it with a soft dry cloth. if s till not completely clear, moisten cloth with one of the following solvents: ?a isopropyl alcohol ?a ethyl alcohol solvents other than those men tioned above may damage the polarizer. especially, do not use the following: ?a water ?a ketone ?a aromatic solvents 10.1.6 do not attempt to disassemble the lcd module. 10.1.7 if the logic circuit power is off, do not apply the input signals. 10.1.8 to prevent destruction of the elemen ts by static electricity, be careful to maintain an optimum work environment. a. be sure to ground the body when handling the lcd modules. b. tools required for assembly, su ch as soldering irons, must be properly ground. c. to reduce the amount of sta tic electricity gene rated, do not conduct assembly and other work under dry conditions. d. the lcd module is coated with a film to protect the display surface. be care when peeling off this protectiv e film since static electricity may be generated.
19/22 rev. 1.0 10.2 storage precautions 10.2.1 when storing the lcd modules, avoi d exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 the lcd modules should be stored under the storage temperature range. if the lcd modules will be stored for a long time, the recommend condition is: temperature : 0 ?? ?? 40 ?? relatively humidity: ? 80% 10.2.3 the lcd modules should be stored in the room without acid, alkali and harmful gas. 10.3 the lcd modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.
20/22 rev. 1.0 appendix a inspection items and criteria for appearance defects items contents criteria leakage not permitted rainbow according to the limit specimen wrong polarizer attachment not permitted not counted max. 3 defects allowed bubble between polarizer and glass <0.3mm 0.3mm ? 0.5mm polarizer scratches of polarizer according to the limit specimen not counted max. 3 spots allowed x<0.2mm 0.2mm ? x ? 0.5mm black spot (in viewing area) x=(a+b)/2 not counted max. 3 lines allowed black line (in viewing area) a<0.02mm 0.02mm ? a ? 0.05mm b ? 2.0mm max. 3 spots (lines) allowed progressive cracks not permitted
21/22 rev. 1.0 appendix b inspection items and criteria for display defects items contents critera open segment or open common not permitted short not permitted wrong viewing angle not permitted contrast radio uneven according to the limit specimen crosstalk according to the limit specimen not counted max.3 dots allowed x<0.1mm 0.1mm ? x ? 0.2mm x=(a+b)/2 not counted max.2 dots allowed pin holes and cracks in segment (dot) a<0.1mm 0.1mm ? a ? 0.2mm d<0.25mm max.3 dots allowed not counted max.3 spots allowed x<0.1mm 0.1mm ? x ? 0.2mm black spot (in viewing area) x=(a+b)/2 not counted max.3 lines allowed black line (in viewing area) a<0.02mm 0.02mm ? a ? 0.05mm b ? 0.5mm max.3 spots (lines) allowed
22/22 rev. 1.0 appendix b inspection items and criteria fo r display defects (continued) items content critera not counted max. 2 defects allowed x ? 0.1mm 0.1mm ? x ? 0.2mm x=(a+b)/2 not counted max. 1 defects allowed a ? 0.1mm 0.1mm ? a ? 0.2mm d>0 max.3 defects allowed transfor- mation of segment max.2 defects allowed 0.8w ? a ? 1.2w a=measured value of width w=nominal value of width

▲Up To Search▲

Price & Availability of TM162JBC7-1SPECS

	To Download TM162JBC7-1SPECS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .